Plumbing 101: A Necessity for Bathtub Installation
Plumbing 101: A Necessity for Bathtub Installation
Blog Article
We've found this post pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround below on the net and thought it made good sense to relate it with you on this site.
Installing a bath tub isn't precisely brain surgery, yet it does need strong plumbing, woodworking, as well as often, tiling abilities. Changing an old bathtub with a new one is also a moderately tough job. If the old tub is conveniently easily accessible, the job can relocate easily; if you have to open up a wall surface to get rid of the old bathtub and place the brand-new tub, the task is a lot harder. In either situation, the project is within a residence handyman's skills, although you will certainly need a helper to leave the old tub as well as set in the brand-new one. See to it you have actually qualified on your own for the task and also fit trying it. Instead of employing a service provider to take control of a halfway-completed project, it is far better to take into consideration employing one before you start. Chances are you may require a specialist plumber to make tube links.
This post will help you mount a brand-new bathtub in your restroom if you have actually already purchased a brand-new bathtub and also don't need to transform the setup of your previous water system pipes.
Your devices and material checklist ought to consist of the following:
Planning for the Installation
First of all, the sustaining structure provided with the bath needs to be fitted (if needed) according to the producer's guidelines. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is essential to make certain that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the faucets system to avoid strain on the tub.
Fit the adaptable faucet connectors to the bottom of the two faucets using 2 nuts and olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be suited its final placement.
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, then the first thing you ought to do is separate the water. After doing so, activate the faucets to drain pipes any kind of water remaining in the system. The process of eliminating the existing taps can be fairly troublesome due to the limited accessibility that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a fabric all set for the continuing to be water that will come from the pipes. When the supply pipes have been eliminated, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary faucets from turning throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Prior to moving on to fit the new faucets, compare the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Setting up the Bath tub
Utilizing the two wood boards under its feet, put the bathtub in the needed setting. The wooden boards are practical in uniformly spreading out the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 little points.
The following objective is to make sure that the bathtub is leveled all round. This can be accomplished by examining the level and also readjusting the feet on the tub till the spirit level reads level.
To mount taps, fit the bottom of the furthest flexible tap port to the proper supply pipeline by making a compression sign up with; then do the same for the other tap.
Activate the supply of water and check all joints and new pipework for leakages and tighten them if needed. Load the bath tub as well as additionally inspect the overflow outlet and the normal electrical outlet for leaks.
Ultimately, take care of the bath paneling as described in the manufacturer's user's manual. Tiling and securing around the bathtub must wait till the tub has actually been utilized at least when as this will certainly settle it right into its last position.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will require a plastic adapter to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and the various other end gives a link to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly need lowering couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the mounting opening in the bath/basin making certain that the washing machines are in area between the tap as well as the sink. Secure the faucet in place with the supplier offered backnut. Once the tap is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular tap connectors. The former type must be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bathroom satisfies the tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the installation can move enough to break a rigid seal, causing the water to pass through the wall between the bathroom and also the tiling, resulting in issues with moisture and possible leaks to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your fixtures and also fittings. They are sold in tubes and also cartridges, and are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with twists of soaked paper or soft rope. Keep in mind to always fill the bath tub with water prior to sealing, to permit the movement experienced when the bathtub is in use. The sealer can crack fairly very early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also quickly readily available on the market. It is a good idea to fit the tiles making use of water-resistant or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our part about Tools You Need to Install a New Bathtub . Thank you so much for taking a few minutes to read our blog post. Are you aware of somebody else who is very much interested in the topic? Take a moment to share it. Thanks for your time. Don't hesitate to come by our blog back soon.
Contact for quality! Report this page